Datamax O'Neil 210216-000 Datenblatt PDF herunterladen

Standard Swivel Lock (210216-000)

Use the Standard Swivel Lock bracket for the 2t and

4t printers (all makes and models).

Parts List:

(1) Standard Swivel Lock

(3) #10 pan head screws [not included; screw length

to be determined by user]

SlimCard Reader Swivel Lock

(210217-000)

Use the SlimCard Reader Swivel Lock bracket for 2t

and 4t SlimCard Reader printers manufactured after

01/01/2004 (all makes and models).

Parts List:

(1) SlimCard Reader Swivel Lock

(3) #10 pan head screws [not included; screw length

to be determined by user]

(2) Bumpers (pre-installed)

Locking Lever

(3) Mounting Holes

Swivel Lock Head

Figure 1

Swivel Lock Base

Locking Lever

Swivel Lock Base

(3) Mounting Holes

Swivel Lock Head

Figure 2

(2) Bumpers

SlimCard Reader Retrofit Swivel Lock

(210222-000)

Use the SlimCard Reader Retrofit Swivel Lock

bracket for 2t and 4t SlimCard Reader printers

manufactured before 01/01/2004.

Parts List:

(1) SlimCard Reader Retrofit Swivel Lock

(3) #10 pan head screws [not included; screw

length to be determined by user]

(2) Bumpers (pre-installed)

Removing the Bumpers

If you are using the 4t SlimCard Reader printer, you

must remove the bumpers from the swivel lock

base. Use the following procedure to remove the

bumpers from the swivel lock base:

1. Remove the bumpers from the swivel lock base

by pulling the bumpers down toward you

(Figure 4).

Locking Lever

Swivel Lock Base

(3) Mounting Holes

Swivel Lock Head

Figure 3

(2) Bumpers

Figure 4

Charger Swivel Lock (210216-001)

Use the Charger Swivel Lock bracket with printers

that are equipped with two charging contact points

(located on the back of the printer's case). When a

printer is attached to the Charger Swivel Lock

bracket, the printer's batteries are automatically

charged.

Parts List:

(1) Charger Swivel Lock

(3) #10 pan head screws [not included; screw

length to be determined by user]

Figure 5

Locking Lever

Swivel Lock Base

Swivel Lock Head

(3) Mounting Holes

(2) Charging points

Selecting a Location

General Guidelines

• If you are using the charger swivel lock, do not

short contacts.

• Use only an Datamax-O’Neil approved power

supply.

• If you are using the charger swivel lock, do not

allow the charging points to come in contact

with metal objects.

• Position the bracket and/or printer with enough

room to properly open and close the printer.

• Position the bracket and/or printer so it is

protected from environmental elements such

as moisture, tools, and boxes.

• Position the bracket and/or printer in a secure

area in normal traffic patterns.

• Do not position the bracket above, near, or

relative to, the driver's position as to interfere

with normal driving operations.

• Mount the bracket and/or printer away from the

driver's head to eliminate potential injury in the

event of an accident.

• Hole centers:

Left to right = 2.324"

Up and down = 1.162" on center

• Only use #10 pan head screws for mounting.

• Datamax-O’Neil does not accept liability for

improperly mounted or poorly placed swivel

locks and/or printers.

Swivel Lock Wall Mount Bracket.fm Page 1 Sunday, February 14, 2010 1:15 AM

1 2

Inhaltsverzeichnis

Seite 1 - Figure 5

Standard Swivel Lock (210216-000)Use the Standard Swivel Lock bracket for the 2t and 4t printers (all makes and models). Parts List:(1) Standard Swive

Seite 2 - Swivel Lock Brackets

Step 2: Attaching the Printer1. Place the printer's swivel mount block over the unlocked swivel lock bracket (Figure 8). 2. Facing the printer, m

Kommentare zu diesen Handbüchern

Keine Kommentare

Datamax O'Neil 210216-000 Datenblatt

Stöbern Sie online oder laden Sie Datenblatt nach Montagesätze Datamax O'Neil 210216-000 herunter. Datamax O'Neil 210216-000 mounting kit Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Related products and manuals for Unknown Electrolux EHL40XWE