Datamax-oneil Class Series Programmer’s Manual Bedienungsanleitung Seite 198
- Seite / 300
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Appendix G – Barcode Details
Class Series Programmer’s Manual 184
F: EAN-13
Valid Characters: 0-9
Length: 13 digits. If the user provides 12 digits, the printer will compute the checksum. If the user
provides the checksum, the printer will check that it matches the expected checksum. If it does not
match, the printer will print all zeros and the expected checksum. See Appendix P.
Valid bar widths: The fourth character of record is the width of the narrow bar in dots. All other bars
are a ratio of the narrow bar (2 times, 3 times, and 4 times the narrow bar width).
The following example prints an EAN-13 bar code:
<STX>L
D11<CR>
1F0000000150100012345678901<CR>
121100000000100Barcode F<CR>
E
G: EAN-8
Valid Characters: 0-9
Length: 8 digits. If the user provides 7 digits, the printer will compute the checksum. If the user
provides the checksum, the printer will check that it matches the expected checksum. If it does not
match, the printer will print all zeros and the expected checksum.
Valid bar widths: The fourth character of record is the width of the narrow bar in dots. All other bars
are a ratio of the narrow bar (2 times, 3 times, and 4 times the narrow bar width).
The following example prints an EAN-8 bar code:
<STX>L
D11<CR>
1G00000001501000123456<CR>
121100000000100Barcode G<CR>
E
- Class Series 1
- Contents 5
- Overview 15
- Typical Data Flow Sequence 18
- Attention-Getters 21
- Control Commands 22
- Immediate Command Functions 23
- Immediate Command Functions 24
- SOH B Toggle Pause 25
- SOH C Stop/Cancel 26
- SOH D SOH Shutdown 26
- SOH F Send Status Byte 27
- STX A Set Time and Date 29
- STX e Select Edge Sensor 32
- STX F Form Feed 32
- STX I Input Image Data 34
- STX k Test RS-232 Port 36
- STX o Cycle Cutter 38
- STX P Set Hex Dump Mode 38
- STX p Controlled Pause 38
- STX Q Clear All Modules 38
- STX q Clear Module 39
- STX R Ribbon Saver On/Off 39
- STX S Set Feed Speed 40
- STX T Print Quality Label 41
- STX X Set Default Module 46
- STX z Pack Module 49
- STX Kb Backfeed Time Delay 54
- STX KC Get Configuration 55
- STX Kc Configuration Set 56
- Table 5-5: Network Setup 87
- Example: 95
- Table 5-13 WiFi Setup 102
- Example 1: 102
- Table 5-14 WiFi Security 103
- (Non-Display Models only) 104
- (MCL Command) 108
- STX Kp Module Protection 110
- Introduction 123
- : Set Cut By Amount 123
- A Set Format Attribute 124
- B Bar Code Magnification 125
- C Set Column Offset Amount 125
- F Advanced Format Attributes 127
- H Enter Heat Setting 129
- J Justification 129
- M Select Mirror Mode 130
- P Set Print Speed 131
- R Set Row Offset Amount 132
- S Set Feed Speed 133
- (Hexadecimal) 137
- Control Codes 139
- STX T Print Time and Date 140
- )s###W Font Descriptor 143
- *c###E Character Code 144
- Generating Label Formats 145
- Printhead Location 145
- Home Position 145
- Generating Records 146
- The Structure of a Record 146
- Record Structure Types 150
- Field Valid Inputs Meaning 150
- Width Multiplier 151
- Height Multiplier 151
- 4. Bar Codes 152
- Polygons 154
- Circles 155
- Advanced Format Attributes 157
- Appendix A 161
- 10K OHM 1/4 WATT 163
- ASCII text file 164
- Appendix B – Sample Programs 165
- Appendix C 173
- Appendix C – Available Fonts 174
- Appendix D 179
- Appendix D – Reset Codes 180
- Appendix E 181
- *Default Symbol Set 185
- Bar Code Summary Data 191
- Bar Code Details 195
- C: UPC-E 196
- E: Code 128 196
- Appendix G – Barcode Details 197
- F: EAN-13 198
- G: EAN-8 198
- I: Codabar 199
- K: Plessey 200
- Q: UCC/EAN Code 128 202
- T: Telepen 204
- byte count 206
- W1c: DataMatrix 209
- W1d / W1D: QR Code 213
- W1f / W1F: Aztec 217
- Barcode W1f 220
- Barcode W1F 220
- W1g / W1G: USD-8 (Code 11) 221
- <STX>L 224
- 34 567890 123 4567 229
- W1z: MicroPDF417 231
- Appendix H 235
- Appendix I 237
- Character Map Selection 239
- Appendix J 241
- I & W-Class GPIO 243
- See the WARNING 245
- • Pins 1 – 2 = +5VDC; 249
- • Pins 2 – 3 = +24VDC; or 249
- WARNING 251
- Signal Out 252
- Signal In 252
- Appendix K 253
- Module ID 256
- Appendix L 257
- Appendix M 259
- Commands by Function 260
- Function Command 260
- Table M-1: Commands (M-Z) 260
- Appendix N 261
- Command Description 263
- (continued) 263
- X X X X X X X 265
- Appendix O 267
- Figure O-2: Sample Label 268
- Appendix P 269
- Appendix Q 271
- ILPC-KANJI Option 272
- ILPC-CHINESE Option 275
- Appendix R 279
- Appendix S 281
- Appendix S – Line Mode 282
- Appendix T 285
- Label Formatting Mode 286
- Appendix T – RFID Details 287
- GEN2 Kill/Access Passwords 290
- GEN2 Lock States 290
- Appendix U 291
- Appendix V 295
- Glossary 297
Verwandte Produkte und Handbücher für Drucker Datamax-oneil Class Series Programmer’s Manual
Drucker Datamax-oneil I-Class Mark II SDIO_USB Host Option Installation Bedienungsanleitung
(6 Seiten)
(6 Seiten)
Drucker Datamax-oneil PrintPAD AN-12 (Line Printer and Easy Print Modes) Bedienungsanleitung
(2 Seiten)
(2 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.024 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern