Datamax-oneil Class Series Programmer’s Manual Bedienungsanleitung Seite 267
- Seite / 300
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Class Series Programmer’s Manual 253
Appendix O
Image Loading
The printer will accept four types of image files: .BMP, .IMG, .PCX and a special Datamax-O’Neil 7-bit
ASCII file (as defined in this section). Using the Datamax-O’Neil 7-bit ASCII format will require at least
twice as much data transmission time as the other formats, (see <STX>I). The Datamax-O’Neil ASCII
image file format is made up of a set of records with identical formats, each representing a dot row of the
image; a terminator follows the last of these records.
Dot-row record
•
•
•
•
Dot-row record
Terminator
Each dot-row record has the following format:
Syntax:
80nndd...d<CR>
Where:
nn
- Is the number of character pairs in dd...d, represented in ASCII hex.
dd…d
- Is dot data, character pairs, ASCII hex, 00-FF.
Duplicate records may be encoded using a repeat data record, following the data record that needs
duplicating. The repeat data record format is:
Syntax:
0000FFnn<CR>
Where:
nn
- Is the number of duplicates, ASCII hex, 00-FF.
The terminator, last record, at the image download is: FFFF<CR>
- Class Series 1
- Contents 5
- Overview 15
- Typical Data Flow Sequence 18
- Attention-Getters 21
- Control Commands 22
- Immediate Command Functions 23
- Immediate Command Functions 24
- SOH B Toggle Pause 25
- SOH C Stop/Cancel 26
- SOH D SOH Shutdown 26
- SOH F Send Status Byte 27
- STX A Set Time and Date 29
- STX e Select Edge Sensor 32
- STX F Form Feed 32
- STX I Input Image Data 34
- STX k Test RS-232 Port 36
- STX o Cycle Cutter 38
- STX P Set Hex Dump Mode 38
- STX p Controlled Pause 38
- STX Q Clear All Modules 38
- STX q Clear Module 39
- STX R Ribbon Saver On/Off 39
- STX S Set Feed Speed 40
- STX T Print Quality Label 41
- STX X Set Default Module 46
- STX z Pack Module 49
- STX Kb Backfeed Time Delay 54
- STX KC Get Configuration 55
- STX Kc Configuration Set 56
- Table 5-5: Network Setup 87
- Example: 95
- Table 5-13 WiFi Setup 102
- Example 1: 102
- Table 5-14 WiFi Security 103
- (Non-Display Models only) 104
- (MCL Command) 108
- STX Kp Module Protection 110
- Introduction 123
- : Set Cut By Amount 123
- A Set Format Attribute 124
- B Bar Code Magnification 125
- C Set Column Offset Amount 125
- F Advanced Format Attributes 127
- H Enter Heat Setting 129
- J Justification 129
- M Select Mirror Mode 130
- P Set Print Speed 131
- R Set Row Offset Amount 132
- S Set Feed Speed 133
- (Hexadecimal) 137
- Control Codes 139
- STX T Print Time and Date 140
- )s###W Font Descriptor 143
- *c###E Character Code 144
- Generating Label Formats 145
- Printhead Location 145
- Home Position 145
- Generating Records 146
- The Structure of a Record 146
- Record Structure Types 150
- Field Valid Inputs Meaning 150
- Width Multiplier 151
- Height Multiplier 151
- 4. Bar Codes 152
- Polygons 154
- Circles 155
- Advanced Format Attributes 157
- Appendix A 161
- 10K OHM 1/4 WATT 163
- ASCII text file 164
- Appendix B – Sample Programs 165
- Appendix C 173
- Appendix C – Available Fonts 174
- Appendix D 179
- Appendix D – Reset Codes 180
- Appendix E 181
- *Default Symbol Set 185
- Bar Code Summary Data 191
- Bar Code Details 195
- C: UPC-E 196
- E: Code 128 196
- Appendix G – Barcode Details 197
- F: EAN-13 198
- G: EAN-8 198
- I: Codabar 199
- K: Plessey 200
- Q: UCC/EAN Code 128 202
- T: Telepen 204
- byte count 206
- W1c: DataMatrix 209
- W1d / W1D: QR Code 213
- W1f / W1F: Aztec 217
- Barcode W1f 220
- Barcode W1F 220
- W1g / W1G: USD-8 (Code 11) 221
- <STX>L 224
- 34 567890 123 4567 229
- W1z: MicroPDF417 231
- Appendix H 235
- Appendix I 237
- Character Map Selection 239
- Appendix J 241
- I & W-Class GPIO 243
- See the WARNING 245
- • Pins 1 – 2 = +5VDC; 249
- • Pins 2 – 3 = +24VDC; or 249
- WARNING 251
- Signal Out 252
- Signal In 252
- Appendix K 253
- Module ID 256
- Appendix L 257
- Appendix M 259
- Commands by Function 260
- Function Command 260
- Table M-1: Commands (M-Z) 260
- Appendix N 261
- Command Description 263
- (continued) 263
- X X X X X X X 265
- Appendix O 267
- Figure O-2: Sample Label 268
- Appendix P 269
- Appendix Q 271
- ILPC-KANJI Option 272
- ILPC-CHINESE Option 275
- Appendix R 279
- Appendix S 281
- Appendix S – Line Mode 282
- Appendix T 285
- Label Formatting Mode 286
- Appendix T – RFID Details 287
- GEN2 Kill/Access Passwords 290
- GEN2 Lock States 290
- Appendix U 291
- Appendix V 295
- Glossary 297
Verwandte Produkte und Handbücher für Drucker Datamax-oneil Class Series Programmer’s Manual
Drucker Datamax-oneil I-Class Mark II SDIO_USB Host Option Installation Bedienungsanleitung
(6 Seiten)
(6 Seiten)
Drucker Datamax-oneil PrintPAD AN-12 (Line Printer and Easy Print Modes) Bedienungsanleitung
(2 Seiten)
(2 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.033 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern